To supply water to the washing machines, they are connected to the water supply using a water inlet hose. Most often, a branch is then made that has a tap so that you can instantly shut off the water supply. The inlet hose for the washing machine comes in a set with the equipment itself - you do not need to purchase it additionally.
However, what should you do if you need to replace it? Replacement may be required for a variety of reasons: leakage, damage to the shell, inappropriate length, or poor quality standard part. To purchase a truly high-quality hose for a washing machine, you need to know their varieties and how much a high-quality inlet hose costs. Just about this and will be written below.
Varieties of the inlet hose
The filling hoses for the washing machine have a very simple device diagram. At the base of the inlet hose is a small polyvinyl chloride pipe, which is reinforced with a reinforced thread and nylon braid. This filling device consists of several layers, which allows us to hope for its strength - they have sufficient resistance against bursts and are ready to withstand high water pressure.
At the end, the filling hoses are reinforced with metal sleeves, fittings and nuts are visible from it. One fitting is screwed to the washing machine, the second to the water pipe. Fittings, nuts are made plastic. They are not particularly strong, so they are tightened by hand, and not with a wrench - this will save them from damage.
This design of the inlet hose is very common - this is how they come with a washing machine. They usually have a certain length. When the washing machine is installed outside the water mains, an extended water inlet hose will be required. These pipes can be purchased separately, the length of such a hose varies from 1 to 6 m. If necessary, the length can be increased by connecting two or more inlet hoses using connectors.
FUM - tape can be used to seal the joints in order to avoid water leakage. However, it is better to exclude such connections, since they cannot be called reliable.
Can the washing machine inlet hoses be disassembled? You can of course do this. However, it is recommended to discard the damaged inlet (inlet) hose and buy a replacement. This way you will avoid possible leaks during the water supply - the new inlet hoses are, of course, more reliable and have serviceable fittings, not to say about the old hose that has been repaired.
See also - Why doesn't water flow into the washing machine - what to do?
Inlet hose with Aquastop
The design that has protection against leaks is called Aquastop. Simple hoses, which were mentioned above, can break - this is due to natural wear and tear. If there are water leaks, you can easily flood the neighbors. Hoses with the Aquastop system neutralize this possibility.
A hose with an Aquastop protection unit is a design where 1 tube goes inside the second. Between them is a special material, when water gets on it, it swells, which triggers the protection valve, which shuts off the water. The system operates as follows:
- normal mode - water flows through the internal, main inlet hose;
- if it is damaged (rupture or slow leakage), water acts on the swelling material;
- the material swells and the valve activates, blocks the water, the floor in the building remains dry.
These hoses have a high price compared to classic ones, however, they give a guarantee of protection against possible leakage. It also happens that the washing machine, even without working, produces a set of water, in which case the hose with the Akvostop system will not help you.
Wrong position of the inlet hoses
It is important that it is positioned in the correct position with respect to connections to the water supply, as well as to the washer. The plastic part of the inlet hose inside must be correctly positioned under the rubber gasket. When swirling, it should equally apply pressure to the gasket on each side. At the place with the lowest pressure during the water supply, a water leak can form.
If water is leaking for this reason, then it is enough that you correctly position the inlet hose and tighten the joints a little more.
Connecting the water inlet hose to washing machines
To connect the inlet hose to the washing machine, you must take care of the connection to the water supply. In this place, a tee and a crane for overlapping are installed, a plastic nut and fitting are screwed to the tee. As a rule, for the entire time of using the washing machine, these operations do not have to be constantly performed, as well as replacing the drain hose.
Professionals advise additionally installing a mechanical filter along with the insert, which purifies the water (in addition to the mesh, which is already installed at the entrance to the machine). Due to this, the washing machine will be protected from dirt. The filter is placed behind the tee, in front of the filling tube.
What to do if the washing machine is not installed near the water supply? In this situation, several inlet hoses can be connected in series. However, a better solution is laying an additional plastic pipe to the installation site of the machine - thus, the chance of avoiding leaks is higher. Accordingly, the taps for locking in any case set at the point of insertion into the main water supply.
When connecting plastic pipes, it is recommended to use the appropriate tool. After the washing machine is running, it is necessary to block the access of water to the machine.
How to screw inlet hose correctly? Some users do this with great effort, but do not do this - there is a high probability of damage to nuts made of plastic. It is necessary to twist them manually, without using tools and other improvised tools that increase effort. It is only necessary to make a tight connection, where the nut will not loosen, and the connection itself will not allow water leaks.
See also:
