With each situation, when the equipment fails. This is especially true of electrical engineering. These moments, often unforeseen, troubles entail financial costs, a lot of effort and time. In particular, the problem becomes even more unpleasant when it comes to frequently used household appliances. This article will talk about What to do if a boiler flows for heating water.
Causes of Problems
First you need to find out the reason why the boiler flowed and choose a solution that is suitable in this situation for correction. Before starting work, an important aspect is the selection of the necessary tools for repair work. Here is an approximate list of what may be needed when servicing a water heater that has become unusable:
- set of tubular and socket wrenches, adjustable spanner, screwdriver;
- multimeter;
- a pair of hoses for the outflow of water;
- a knife may be needed if necessary.
The above tools must be available to any owner. If, nevertheless, some of them are missing, be sure to purchase at any hardware store.
At first glance, it might seem that working with such an aggregate as a boiler will not be difficult, but alas, this opinion is erroneous. At least for a novice in the industry. But having received certain knowledge, even a person without work experience will be able to cope with this problem, especially if it is about the boiler flows below.
See also - How to install and connect a water heater yourself
Troubleshooting options
So, if you noticed that your water heater is flowing, you need to do two things: disconnect it from the mains and conduct a thorough inspection of the place where the leak is observed. There are several reasons for the appearance of smudges:
- factory defects, violation of technical rules during assembly;
- during prolonged operation of the unit, during which the proper preventive maintenance was not carried out to maintain operability;
- lack of a magnesium rod in the tank;
- water has many impurities or is very hard;
- during initial installation, the device was not grounded.
In any of the above cases, the tank can be dismantled and repaired, or even replaced with a new one. When water flows through the thermostat cover, the problem is quite serious and the devices are out of order. If smudges come from the joints of the water pipes, this means only one thing - the tightness of the device is broken. In this case, the tank can not be fixed, it must be replaced.
It also happens that with inaccurate installation of a water heater, the housing may be deformed, which often leads to leakage.The problem may not be immediately noticed, but if you notice it, you must take the following actions:
- stop using the heater;
- to inspect the alleged location of deformation (most often it is a safety valve);
- empty the tank and attempt repair. Or call the wizard from the service center in order to probably find out what the problem is and fix it.
If the Termex water heater flows somewhere from above, and no deformations are found, and the tank is regularly serviced and in perfect condition, it is recommended to hand it over under the warranty period. If the magnesium rod has not changed for a long time, then the tank, if it is not enameled inside, has rotted through and through, and then it must be replaced without fail.
Water flows through the piping, which indicates poor installation when connecting the boiler to the water supply. Many people install plastic pipes for themselves, but do not install safety valves, which, in the end, leads to water hammer. If such problems are found, it is necessary to redo the water supply system. If the valve itself leaks, then the tank is working.
In case of leakage of the tank cap located below, it is required to check the heater. After all, it is precisely because of the formation of scale on it that a leak can form. Sealing or sealing on the device may also be impaired. Repair consists in replacing the heating device, as well as fixing the holder of the latter.
Is it possible to repair a leaked boiler?
In most cases, when a leak occurs in the tank itself, it is almost impossible to repair it, since the boiler is a monolithic structure covered with enamel, which if damaged, it will not be possible to fix it except to replace the boiler with a new one.
When it comes to boiler tank leaks, there are several ways to repair it:
- to solder the appeared openings on the tank case. This will save the tank, but for a short time, then you still have to change it;
- to seal the places of water leakage, which will also help, but not for long;
- if there is the same tank, but with a faulty heater, you can replace it.
Conclusion
We have painted all the options for you, why the boiler is leaking, and described options for how to fix its malfunctions, but in some cases it is better to call the master, since during repair work you may accidentally damage the integrity of the tank, or the enamel coating. If you are confident in your abilities, then you can start work.
See also:
- The 6 Best Hotpoint-Ariston Water Heaters
- The 8 best Zanussi water heaters of the year
- The 8 Best Thermex Water Heaters of the year
- 10 best Timberk water heaters of the year
- 10 best Gorenje water heaters of the year
